DIY Flower Scrunchie - My Golden thimble

In progress

A make by fudge1_1mellow

About this make

Lightweight Woven Fabric – Cotton works best! I used a soft gingham I had leftover from my shirred crop top. You only need a small piece, so it’s a great scrap buster! ¼” Wide Elastic – Just cut a piece that fits comfortably around your wrist (around 6–7 inches works for most people). Matching Thread – Because visible thread isn’t cute when you want the fabric to shine. Sewing Machine – Any machine will do, as long as it’s ready to handle a simple straight stitch. Fabric Scissors – To cut out your flower scrunchie pattern pieces. Pins or Clips – To hold everything together before stitching. Optional but very handy: Loop Turner – Makes turning the tube of fabric right-side out soooo much easier. Bodkin or Safety Pin – For inserting the elastic with zero frustration (you’ll thank me later). 1. Fold and Press Your Fabric First, cut a rectangle of fabric that measures 6 ½” by 18” long. Fold your fabric lengthwise with the right sides facing each other. Give it a quick press with your iron to create a nice crisp crease. This will help keep everything neat when we cut out the shape. 2. Trace and Cut the Flower Shape Now, grab your flower scrunchie pattern and place it on the fabric with the straight edge lined up along the fold. This part is important so your scrunchie comes out symmetrical! Use some pins or fabric clips to hold it steady and trace around the pattern. You’ll see the flower shape coming together already, and we haven’t even sewn a stitch yet. 3. Sew Around the Petals Start stitching just before the first curve (you’ll see it on the pattern), and don’t forget to backstitch at the beginning so everything stays secure. Then just keep following the outline, gently guiding your fabric along all those cute curves. As a tip, I recommend lowering and raising the presser foot as needed to rotate the fabric as you go. Just make sure you leave the needle down! 4. Snip and Trim the Curves Once that’s done, we need to do a little trimming magic. Make a small straight cut at each of the corners or marked points. If you have pinking shears—yay! Use them to trim around the curves. If not, just make tiny triangle-shaped notches around the curves, and trim down the seam allowance. And cut along the lines for the side tabs, too. This helps everything lay flat when we turn it right side out. 5. Turn It Right Side Out Now the satisfying part—turning it right side out! I used my loop turner, but if you don’t have one, a pencil or even a straw and a chopstick will do the trick. Take your time with this step, especially around those petals. 6. Fold and Press the Tab Once it’s turned, give your flower scrunchie a good press to smooth out all those curves and help shape it. Fold one of the side tabs inward neatly. This is where we’ll close things up later. 7. Sew the Elastic Casing Now, using your ruler or seam gauge, measure ¼” in from the folded edge and draw a straight line across the whole scrunchie. This will become our elastic casing. Sew along that line with a straight stitch, backstitching at both ends to secure it. 8. Thread the Elastic Through Next, we’re threading the elastic! Wrap the elastic around your wrist and overlap it about 2”-3” and cut that length. Grab your bodkin or a safety pin and slide the elastic through the casing. Be gentle and make sure the elastic doesn’t twist inside—this part can be fiddly, but you’ve got this. 9. Sew the Elastic Ends Together Once both ends of the elastic are out, overlap them slightly (those 2” or 3” from the last step). And sew them together with a zigzag stitch. I like to go back and forth a couple of times for extra strength. 10. Close the Scrunchie Now we’re almost done! Tuck the raw side tab into the folded one, lining it up neatly, and then finish your scrunchie with a straight stitch across the seam. Give it one last press—and you’re done! You just made the cutest little DIY Flower Scrunchie!!

Sewing diary

  1. Started this make 30th of October 2026